Product quality requirements - Bonsai pot 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2. 11-12 "basin body is not allowed to exceed 4, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue in the basin, the bottom hole should not be pricked, and small holes should be opposite. 5. Glaze bubble: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the surface (4 to 6 inches, 2 allowed 7 to 8 inches, 3 allowed 10 to 12 inches, 4 allowed). 6. Slag (impurities): The surface of the surface should be pricked and not allowed to go too far. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or contact between the body and external objects during firing, or accumulation of thick glaze water at the bottom, It is not allowed to pass through defects on the bottom or visible surface (thick glaze feet can be polished without pricking hands). 8. Shrinkage glaze: it is not allowed to pass through the mouth, and other parts are within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the green body or blackening. The support can pass through (except for the AO. PR mouth surface, which can be relaxed by 50%). 9. Collision and impact: It is caused by human collision or impact when the product comes out. At the bottom or non visible surface, it can be repaired. 10. The feet should be flat and free of cracks, and the feet can be repaired except for small cracks. The inner cavity should be clean and free of debris. 11. With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. Control the size and weight of the product. 2: Refining basin 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2. 11-12 "basin body is not allowed to exceed 4, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue in the basin, the bottom hole should not be pricked, and small holes should be opposite. 5. Glaze bubble: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the surface (4 to 6 inches, 2 allowed 7 to 8 inches, 3 allowed 10 to 12 inches, 4 allowed). 6. Slag (impurities): The surface of the surface should be pricked and not allowed to go too far. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or contact between the body and external objects during firing, or accumulation of thick glaze water at the bottom, It is not allowed to pass through defects on the bottom or visible surface (thick glaze feet can be polished without pricking hands). 8. Shrinkage glaze: it is not allowed to pass through the mouth, and other parts are within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the green body or blackening. The support can pass through (except for the AO. PR mouth surface, which can be relaxed by 50%). 9. Collision and impact: It is caused by human collision or impact when the product comes out. At the bottom or non visible surface, it can be repaired. 10. The feet should be flat and free of cracks, and the feet can be repaired except for small cracks. The inner cavity should be clean and free of debris. 11. With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. 12. The inside of the basin should be clean, with uniform length and direction of fine lines, and all four legs should be flat Control the size and weight of the product. 3:
Orchid Pot 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2. 11-12 "basin body is not allowed to exceed 4, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue in the basin, the bottom hole should not be pricked, and small holes should be opposite. 5. Glaze bubble: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the surface (4 to 6 inches, 2 allowed 7 to 8 inches, 3 allowed 10 to 12 inches, 4 allowed). 6. Slag (impurities): The surface of the surface should be pricked and not allowed to go too far. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or contact between the body and external objects during firing, or accumulation of thick glaze water at the bottom, It is not allowed to pass through defects on the bottom or visible surface (thick glaze feet can be polished without pricking hands). 8. Shrinkage glaze: it is not allowed to pass through the mouth, and other parts are within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the green body or blackening. The support can pass through (except for the AO. PR mouth surface, which can be relaxed by 50%). 9. Collision and impact: It is caused by human collision or impact when the product comes out. At the bottom or non visible surface, except for those that can be repaired. 10. With brackets: The color of the brackets should be basically the same, the brackets should be fully glazed, the brackets should not be too small, and the proportion should be moderate. 11. The inside of the basin should be clean and free of mud and debris, and the walls should be clean. The flower picking area should be neatly organized and not pricked. The flower picking pattern should meet the requirements of the sample, and the size and weight of the product should be controlled. 4: Moisturizing basin 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass through) The bottom is cracked, not worn through, and can be repaired (including foot mounting). 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue inside the basin. 5. Glaze bubbles: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the visible surface (4-6 ″, 2 allowed) 6. Slag (impurities): Impurities on the surface of the mouth and visible surface are not allowed to pass through. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or the contact between the body and external objects during firing, or the accumulation of thick glaze water at the bottom, resulting in defects on the visible surface, are not allowed to pass through (thick glaze feet cannot pass through after polishing) 8. Shrinking glaze: The mouth is not allowed to pass through, Other parts within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the body or blackening (except for the AO. PR surface, which can be relaxed by 50%). 9. Collision and impact: It is the result of human collision or impact when the product comes out, causing the impact. At the bottom or non visible surface, it can be repaired. 10. The inner cavity should be clean and free of debris. Ensure that the inner liner is permeable, the outer shell is not leaking, and the inner liner sleeve outer shell has some gaps that can rotate smoothly. Control the size and weight of the product. 4: Diandian Pot 1. Cracking: The edge of the product's mouth. (No matter the inner or outer opening, it is not allowed to pass) The bottom is cracked and not penetrated, and repair can pass. 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue inside the basin. 5. Glaze bubbles: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the visible surface (4-6 ″, 2 allowed) 6. Slag (impurities): Impurities on the surface of the mouth and visible surface are not allowed to pass through. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or the contact between the body and external objects during firing, or the accumulation of thick glaze water at the bottom, resulting in defects on the visible surface, are not allowed to pass through (thick glaze feet cannot pass through after polishing) 8. Shrinking glaze: The mouth is not allowed to pass through, Other parts within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the body or blackening (except for the AO. PR surface, which can be relaxed by 50%). 9. Collision and impact: It is the result of human collision or impact when the product comes out, causing the impact. At the bottom or non visible surface, it can be repaired by 10 With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. 11. The inner cavity should be clean and free of debris. Make every point clear and have a sense of unevenness. Control the size and weight of the product. 5. Blank type 1. Cracking: The edge of the product. (No matter the inner or outer opening, it is not allowed to pass) The bottom is cracked and not penetrated, and repair can pass. 2. Deformation: The diameter should not exceed 2%, the mouth surface should be flat without height, the shape should be regular, and the mouth line should be uniform. 3. Knots: There are protruding nodular solid bodies in the basin, which are not allowed to pass through without pricking hands. The protruding solid bodies of the underglaze glaze body are less than 5mm, which are not pricked or dense, and can pass through up to 2; If it exceeds, it is not allowed to pass. (4-6 "basin body is not allowed to exceed 2, and one side is not allowed to exceed 2. 7-8" basin body is not allowed to exceed 3, and one side is not allowed to exceed 2.) 4. Mud residue: There should be no mud residue inside the basin. 5. Glaze bubbles: There are small bubbles on the surface of the glaze, and dense visible surfaces are not allowed to pass through. Molten hole: The mouth surface is not allowed to pass through. Pinholes: Dense small holes on the visible surface (4-6 ″, 2 allowed) 6. Slag (impurities): Impurities on the surface of the mouth and visible surface are not allowed to pass through. 7. Sticking feet, scars, and nail plates: Defects caused by the bottom of the body sticking to the kiln equipment or the contact between the body and external objects during firing, or the accumulation of thick glaze water at the bottom, resulting in defects on the visible surface, are not allowed to pass through (thick glaze feet cannot pass through after polishing) 8. Shrinking glaze: The mouth is not allowed to pass through, Other parts within 1cm ² Limited to 3 locations. Not dense, can be repaired. Orange glaze (orange peel): The glaze surface is in the shape of an orange peel, and large areas are not allowed to pass. It is not allowed to pass through the mouth, only for non visible meetings. Small areas can be passed through. Thin glaze: The glaze layer is too thin, and it is not allowed to pass through the body or blackening (except for the AO. PR surface, which can be relaxed by 50%). 9. Collision and impact: It is the result of human collision or impact when the product comes out, causing the impact. At the bottom or non visible surface, it can be repaired by 10 With tray: The color of the tray should be basically the same, the tray should be fully glazed, the tray should not be too small, and the proportion should be moderate. 11. It is required that the bottom of the basin be cut off, the bottom of the basin be clean and free of mud debris, the cut off area should be smooth, the edge holes should be round, and the basin holder should not deviate. Glazing should be done in place (especially in the area between the basin supports), and the second batch should not pass through. If it is a two-piece or three-piece set, it must be done well, and it should not exceed the height of the six handmade types (including even pottery pots) The mouth surface cracks and does not penetrate properly, and repair can pass 2 The large basin has vertical or horizontal openings around it. If it doesn't break, it can pass 3 The bottom cannot be nailed or missing meat. It can be repaired, but it should be flat and not exceed the visible surface at the bottom Impurities do not prick hands, have a small area, and are not dense enough to pass through. The shrinkage area is small and not dense, which can be repaired (10-14 "can have 2 to 3 places, the whole body cannot exceed 3 places, 18-24" can have 3 to 4 places, the whole body cannot exceed 4 places) 5 The deformation can pass within the range of ± 4% for 10-14 "and ± 5% for 18-24" The patterned and dotted lines should be clear, and the lines should be clear. The Haff line should not be clearly glazed, and the large pot should be in place with neat lines and edges. There should be no missing glaze, thin glaze, or thick glaze attached. Packaging quality requirements: 1 The size of the cardboard box should meet the requirements, and the cardboard box should be clean and tidy with a clear description The incoming product should be clean and dust-free. Stick the foot in place, stick the barcode well, and label the cardboard box product with one variety, one color, and one pallet. It is absolutely not allowed to exceed two varieties and two colors (except for special cases, such as self use pots, except for special small orders). 3. The manual pot packaging must be in place, and the paper or soft strips inside the pot must be in place to prevent collisions between pots. The upper pot must be separated from the pot by cardboard, and the inverted pot must be placed with more paper or soft strips to prevent collisions when holding the pot.
Yixing Bocai Pottery Co.,Ltd
